Aube-technologies TH104 Bedienungsanleitung PDF herunterladen (Seite 1)

This thermostat has been designed to control a RESISTIVE load

not exceeding 3500 W @ 240 VAC or 1750 W @ 120 VAC, such as

electric baseboards, convectors, radiant ceilings, floor heating sys-

tems, etc.

It is not compatible with a low voltage controller used by a cen-

tral heating system or systems using a contactor or a relay

whose current is under 2 A.

TURN OFF POWER TO THE HEATING SYSTEM AT THE

MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK.

Installation should be carried out by an electrician.

This thermostat is designed to be used with a self-pro-

tected heating system equipped with linear limit control

and circuit breaker.

For a new installation, choose a location about 5 ft. (1.5 m)

above the floor, facing the heating system and on an inside

wall.

Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or con-

cealed chimneys or stove pipes.

All cables and connections must conform to the local electrical

code.

Special CO/ALR solderless connectors must be used when

connecting with aluminum conductors.

The wires are not polarized, therefore the connections can be

made on either terminal.

PROVIDED PARTS

! One (1) TH104 thermostat

" Two (2) 6-32 mounting screws

# Two (2) solderless connectors

1) Connect the thermostat

Connect the rear wires to the power and load using solderless con-

nectors for copper wires.

INSTALLATION

TH1 04

Installation Instructions and Owner s Guide

Current program

number when the

Automatic mode

is active

Room

temperature

Heating

indicators

Current time

and day

Manual

mode

Automatic

mode

Econo

mode

Current program

number when

Econo schedule

is active

FAN: displayed when

conventional temperature

control is selected

LP: displayed

during a power

failure

SETPOINT:

displayed when

viewing or

setting the

temperature

TIME: displayed

when time needs

to be adjusted

Temperature

adjustment

buttons

MODE: to select the

desired operating mode

To set the day

To set the

time

To set the

minutes

To access

programming mode

and view programs

To exit a function

RESET:

To reset the

thermostat

4 WIRES

2 WIRES

1/4 400-104-000-A

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - INSTALLATION

This thermostat has been designed to control a RESISTIVE loadnot exceeding 3500 W @ 240 VAC or 1750 W @ 120 VAC, such aselectric baseboards, convector

Seite 2 - OPERATING MODES

2) Secure the thermostatPush the excess wire intothe electrical box to preventinterference with the thermostat.Secure the base to the electricalbox us

Seite 3 - ECONO SCHEDULE

ECONOThis mode automatically runs the programs of theEcono schedule. Press MODE until ECONO is outlined.The current program number is displayed above

Seite 4 - ABOUT TEMPERATURE CONTROL

Model: TH104Supply: 120/240 VAC, 50/60 HzPower consumption (off): 860 mWLoad: 14.6 A maximum (resistive only), 2 A minimumPower: 1750 W @ 120 VCA / 35

Seite 5 - LOCKED KEYBOARD

TH104-SW PROCEDURELOCKED KEYBOARDMAINTAINING THE TEMPERATURE AROUND THE CLOCK1- Press the MODE button to place the thermostat inECONOMY mode.2

Kommentare zu diesen Handbüchern

Keine Kommentare

Aube-technologies TH104 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schalttafel Aube-technologies TH104 herunter. Aube Technologies TH104 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Aube-technologies TH104 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schalttafel Aube-technologies TH104 herunter. Aube Technologies TH104 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Aube-technologies TH104