Aube Technologies TH147E-P Bedienungsanleitung PDF herunterladen

TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 1/4

The TH147E-P and TH148ELE-P thermostats can be used to control:

• a forced air system - 2 or 3 wires

• a hot water system with or without pump - 2 wires

• a millivolt system - 2 wires

Note: The installation must be performed by an electrician.

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT

POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

o Identify and label each wire (with the corresponding letter on the

wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 6 mm).

2.2 Installing the New Baseplate

Choose a location approximately 1.5 m above the floor and on

an inside wall. Avoid draughty areas (top of staircase, air outlet,

etc.), dead air spots (behind doors), direct sunlight or areas near

concealed pipes or chimneys.

n Remove the thermostat faceplate.

o Loosen the locking screw in order to separate the thermostat

from its baseplate (the screw cannot be completely removed).

p Gently tilt the thermostat upwards.

q Pass the wires through the opening of the baseplate and secure

the baseplate to the wall using the appropriate screws.

2.3 Terminal Designations

Introduction

Features

TH147E-P

TH148ELE-P

Pump protection X X

Programmable cycle length X X

Battery replacement indicator X X

Backlit display X X

Programming:

- Preprogrammed schedule

- Temporary bypass

- Time display (12 h or 24 h)

Interchangeable faceplates X X

Unoccupied mode activated remotely X

Automatic daylight savings changeover X

Display

Adjustment

buttons

Backlight

button

Comfort

temperature

preset

Mode selection /

program exit

Program

button

Economy

temperature

preset

Temperature

Schedule

Time

Manual mode

Heating is On

: Comfort temperature indicator

: Economy temperature indicator

Day

Display

Appears when the

setpoint temperature

is displayed

Low battery indicator

Automatic mode

Unoccupied mode

Installation

R Power

W Load

Un / Un Unoccupied mode input (TH148ELE-P only)

TH147E-P & TH148ELE-P

Installation and User Guide

Programmable Thermostats

400-147-016-C (TH147_148 P Europe) ENG.fm Page 1 Tuesday, January 8, 2008 2:47 PM

1 2 3 4

Inhaltsverzeichnis

Seite 1 - TH147E-P & TH148ELE-P

TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 1/4The TH147E-P and TH148ELE-P thermostats can be used

Seite 2 - Basic Functions

TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 2/42.4 Connecting the Heating System2.5 Unoccupied Mode

Seite 3 - Programming

TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 3/43.5 Control Mode3.5.1 ManualUse this mode to set the

Seite 4 - Technical Assistance

TH147E-P & TH148ELE-P 400-147-016-C 2008-01-08 4/4n Press the backlight button until the configuration

Kommentare zu diesen Handbüchern

Keine Kommentare

Aube Technologies TH147E-P Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Thermostate Aube Technologies TH147E-P herunter. Aube Technologies TH147E-P User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Thermostate Aube Technologies TH147E-P